If you are approved, then your refund will be processed, and a credit will automatically be applied to your credit card or original method of payment, within a certain amount of days. We will also notify you of the approval or rejection of your refund. Once your return is received and inspected, we will send you an email to notify you that we have received your returned item. Any item that is returned more than 10 days after delivery Refunds Any item not in its original condition, is damaged or missing parts for reasons not due to our error. There are certain situations where only partial refunds are granted (if applicable) Please do not send your purchase back to the manufacturer. To complete your return, we require a receipt or proof of purchase. Several types of goods are exempt from being returned. It must also be in the original packaging. To be eligible for a return, your item must be unused and in the same condition that you received it. If 10 days have passed since your purchase, we can’t offer you a full refund or exchange. Our refund and returns policy lasts 10 days from the date of delivery. Status LED which blinks during communication with the PCġ× ST-Link V2 Mini STM8 STM32 Simulator Download Programmer.Direct firmware update feature supported (DFU).SWIM cable for connection to the application.SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed.SWIM low-speed and high-speed modes supported.1.65 V to 5.5 V application voltage supported on SWIM interface.SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector.With 4 DuPont lines, so you can easily respond to different target board line orders!.Red and blue color LED indicator, allowing you to always observe ST-LINK V2 working condition!.500MA internal resettable fuse, complete protection of your expensive computer motherboard!.Shell characters using laser engraving, never fade off! Permanent clarity!.5V and 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V.Interface definition directly marked on the shell, clear, convenient, and practical!.PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable!.Make sure you connect the correct pins from the output port to the Microcontroller you are using. Supported devices: STM8 devices with SWIM interface and STM32 devices with SWD interfaceĪs is has a USB 2.0 port onboard so you can just plug it in the PC and download the programming or debugging software you are planning to use and start working on it.Supported software: ST-LINK Utility v2.0, STVD Version 4.2.1, STVP Version 3.2.3, IAR EWARM, IAR EWSTM8 Revision v1.30, KEIL RVMDK Revision v4.21, ATOLLIC.Automatically Upgradable firmware to support more devices.Programming: supports FLASH ROM, EEPROM, AFR, etc.Debugging: run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.Standard USB interface for direct connection to PC.Dual voltage output (3.3V/5V), easy for debugging and programming. Onboard 500mA self-recovery fuse to avoid short circuit.The U disk aluminum housing protects the simulator from static electricity and wear and tear due to rough use and provide protection against shocks, operational errors and malfunction. It supports both 3.3V and 5V to easily connect the MCU. It has USB 2.0 to connect to your PC and SWIM/SSD interface for communication with microcontrollers. It is a toned down version of ST link V2 In line programmer/ debugger for STM8 and STM32 microcontrollers. It is an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32 microcontrollers from ST Microelectronics. JTAG cable for connection to a standard JTAG 20-pin 2.This is a Mini ST-LINK/V2 on a small single board.1.65 V to 3.6 V application voltage support on the JTAG/SWD interface and 5 V tolerant inputs.JTAG/serial wire debug (SWD) specific features:.SWIM cable for connection to an application with pin headers or 2.54 mm pitch connector.SWIM cable for connection to an application with an ERNI standard connector Vertical connector reference: 284697 or 214017 Horizontal connector reference: 214012.SWIM programming speed rates: 9.7 kbyte/s in low-speed, 12.8 kbyte/s in high-speed.SWIM low-speed and high-speed modes support.1.65 V to 5.5 V application voltage support on the SWIM interface.USB 2.0 full-speed compatible interface.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |